短模型上的明渠非恒定流试验

水工整体模型试验中,明渠非恒定流至今大多被简化为恒定流,而效果有时并不理想。本文指出,只要设置固定式曲线尾门,并有必要的动态量测设备,便可模拟原型非恒定流;即使模型偏短,也能得出比恒定流试验更接近原型的成果。在同一模型上,既做恒定流试验,又进行必要的非恒定流试验,二者相辅相成,必将有助于试验水平的提高。作为例证,本文介绍了泄洪调度导致航道水面波动的一项试验成果,并以岩基冲刷、通航水流条件、围堰过水、河床冲淤等研究课题为例,讨论了采用“短模型非恒定流试验方式”的必要性与可行性。     

The relation between luminous properties and oxygen content inZnS:TbOF thin-film electroluminescent devices fabricated byradio-frequency magnetron sputtering method

The purpose of this paper is to study the relationship between the oxygen concentration and brightness degradation in ZnS:TbOF green thin-film electroluminescent (EL) devices. The characteristics including crystallinity, optical, and electrical properties were discussed. The brightness-voltage (B-V) measurement results shelved that with higher oxygen-content in ZnS:TbOF phosphor layer, lower brightness was measured. It was consistent with the poor crystallinity, worse photoluminescent intensity, and easier to get moisture in the oxygen-rich (O/Tb>1) phosphor film. Furthermore, deep level transient spectroscopy (DLTS) measurements identified that when the O/Tb ratio was greater than 1, the oxygen-related deep hole traps E_H1 and/or E_H2 could be detected in the ZnS:TbOF phosphor layer. These E _H1 and/or E_H2 traps were believed to be the main killers for the brightness of the device since they capture most of the holes from the generated electron-hole pairs. This evidence strongly supports that the modified energy transfer model is more dominant than direct impact excitation during the luminescent process     

In-laboratory removal of femoral sheath following protamine administration in patients having intracoronary stent implantation

Two hundred twenty-eight patients with successful coronary stent implantation were randomized either to protamine administration and femoral sheath removal (group I, n = 117) or no heparin neutralization and delayed sheath removal (group II, n = 111). The hospital stay after treatment was shorter in patients receiving protamine; therefore, protamine use for neutralizing circulating heparin may be safely administered immediately after stent implantation.     

吸附精制提高催化裂化柴油的安定性

用卸出的催化裂化平衡催化剂对催化裂化柴油进行吸附精制，取得了很好的效果。精制油收率99％以上，其安定性达到了优级轻柴油的标准（沉渣＜2．0mg／100mL，色号≤16）。精制后柴油的胶质下降约1个百分点，对吸附物的组成分析表明，其氮含量是柴油的17倍以上。对精制油的分析表明，吸附精制可明显降低柴油的酸度和碱性氮化物的含量。     

气—液式热管换热器在硫酸工业中的应用研究

本文研制的气－液式热管换热器应用于硫酸生产中ＳＯ３气体的余热回收。它具有传热性能好、流动阻力小、寿命长、体积小、节能效果显著和易清垢等优点。     

变结构变参数设计方法及其在机械CAD中的应用

提出了一种新颖的机械结构设计思想－变结构变参数设计方法，并结合实例，阐述了变结构变参数设计的概念、原则、实施措施和意义。由此对Ｉ－ｄｅａｓ软件包进行了二次开发，编制了发动机曲轴专用ＣＡＤ软件程序，并用某型号发动机曲轴进行了验证。     

Assessment model of dam operation risk based on monitoring data

Although the dams produce remarkable social and economic benefits, the threat made by unsafe dams to the life and property of people who live in the lower river area is un-negligible. Based on the monitoring data which reflect the safety condition of dams, the risk degree concept is proposed and the analysis system and model for evaluating risk degree (rate) are established in this paper by combining the reliability theory and field monitoring data. The analysis method for risk degree is presented based on Bayesian approach. A five-grade risk degree system for dam operation risk and corresponding risk degree is put forward according to the safety condition of dams. The operation risks of four cascade dams on some river are analyzed by the model and approach presented here and the result is adopted by the owner.     

Effects of various post-treatments on carbon nanotube films for reliable field emission

In this report, the FE characteristics of carbon nanotubes (CNTs) treated using both thermal annealing and mechanical coatings on the as-grown CNTs systematically studied. It was found that in the high temperature annealed samples, CNTs were attacked at its root during annealing due to a small amount of oxygen, and were pulled out of the substrate in places after FE measurements because of the contact resistance. However, for the mechanically coated samples both with spin on glass (SOG) and polymethyl methacrylate (PMMA), CNTs were found to be nearly intact after FE measurements and showed reliable FE characteristics over repeatable voltage scan. The reliability of CNTs during FE could be owing to the strong adhesion of CNTs to the substrate both by SOG and PMMA coatings.     

The critical pressure and impeding pressure of Al evaporation during induction skull melting processing of TiAl

In this article, two key pressures, the critical pressure P _crit and the impeding pressure P _impe of elemental evaporation, are defined and studied based on the calculation relationship between the evaporation loss rate N _m and the chamber pressure P during melting of titanium-aluminum alloys. When the chamber pressure is below P _crit or above P _impe, N _m tends to the maximum or the minimum value and remains almost unchanged. However, if P _crit<P<P _impe, with the increase of the chamber pressure, N _m declines sharply. A method has been put forward to calculate P _crit and P _impe of Al evaporation in a Ti-XAl (at pct) (X=25 to 50) melt. The calculation result shows that P _crit or P _impe is a second-order function of the molar percentage of Al and the melt temperature.     

新增探明储量的经济可采储量计算方法

提出了新增探明储量有无经济可采储量的判别方法。在此基础上，通过对立已开发油田技术可采储量经济转化率与油藏空气渗透率的相关关系式和图版，根据储层的空气渗透率，计算新增探明储量的经济转化率和经济可采储量。该方法参数易取，计算简便，对于快速、准确计算新增探明储量的经济可采储量具有重要意义。